| Weights |
| Empty Weight | 549998.2 lb
| | Gross Weight | 1270021.3 lb
| | Weight | 89999.4 lb
| | Weight (Dry) | 24802.1 lb
| | Weight (Wet) | 25904.4 lb
|
|---|
|
| Engine & Fuel System |
| Engine Make | 2238
| | Engine Model | SSDA18V170
| | Fuel Tank | 1400.2 gal
| | Fuel Type | diesel
| | Horse Power: Sae J1995 | 3500.1 hp
| | Number Of Cylinders | 18
| | Power Measured @ | 1900 rpm
| | Cooling System | 190 gal
| | Displacement | 4759.9 cu in
|
|---|
|
| Drive System |
| Emergency Brakes | Oil-cooled, multiple disc front & rearAutomatically applied prior to hydraulic system pressure dropping below level required to meet secondary stopping requirements.
| | Parking Brake Type | Multiple disc, spring-applied, hydraulically-released, dry brakes on inboard end of each wheel motor rotor shaft. Rated to hold on ±15% grade at maximum gross vehicle weight.
| | Service Brake Type | Oil-cooled, hydraulic-actuated, multiple disc brakes at each wheel.
| | Wheel Brake Locks | Switch-activated
| | Hoist And Steering | Dual, in-line, high pressure
|
|---|
|
| Operating Specs |
|
|
| Hydraulic System |
| Hydraulic System | 350.1 gal
| | Pumps | Two pumps, single package, end of alternator
| | Filtration | In-line replaceable elements
|
|---|
|
| Dimensions, Wheels & Tires |
| Standard Tire | 53/80 R63
| | Wheelbase | 21.82 ft in
| | Width Over Tires-Front | 24.68 ft in
| | Width Over Tires-Rear | 27.33 ft in
| | Motorised Wheels | GDY108 Induction Traction Motors
| | Turning Radius | 52.5 ft in
| | Overall Length | 51.19 ft in
| | Overall Height | 24.18 ft in
| | Front | 328
| | Rear | 239
|
|---|
|
| Battery & Electrical System |
| Alternator | 24 volt, 250 amp
|
|---|
|
| Transmission |
| Motor Gear Box | 25.1 gal
| | Maximum Speed (Km/H) | 64.5
|
|---|
|
| Technical Specs |
| Ratio | 32.62:1
| | Control | AC Torque Control System
| | Lighting | 24 volt
| | Cranking Motors | Two/24 volt
| | Capacity - Struck | 194.9 yd3
| | Heaped (2:1, Sae) | 280 yd3
| | Payload | 89999.4 lb
| | Structure | Flat floor configuration
| | Canopy Sheet | 06 mm 0.24' 690 Mpa 1,00,000 psi tensile strength steel
| | Front Sheet | 10 mm 0.39' Outer, 12 mm 0.47' Center, 1379 mPa 200,000 psi tensile strength steel
| | Side Sheet | 10 mm 0.39' 1379 Mpa 2,00,000 psi tensile strength steel
| | Floor Sheet | 16 mm 0.63' Outer, 19 mm 0.75' Center, 1379 mPa 200,000 psi tensile strength steel
| | Loading Height | 23.5 ft in
| | Crankcase | 90.1 gal
| | Hoist Cylinder | Two 3-stage dual-acting outbound cylinders and internal cushion valve, over-centre damping.
| | Relief Pressure | Hoist and brake cooling- 17237 kPa 2,500 psi Steering and brake-20685 kPa 3,000 psi
| | Hoist Time | Power-up loaded: 24 sec, Power-down: 14 sec, Float-down empty:24 sec
| | Turning Circle Diameter (Sae) | 105 ft in
| | Reservoir | 250 gal
| | Suction | Single, full flow, 100 mesh
|
|---|
|