Weights |
Empty Weight | 323998 lb
| Gross Weight | 724000.3 lb
| Weight | 13589.3 lb
|
---|
|
Engine & Fuel System |
Engine Make | 2238
| Engine Model | SSA16 V159E-2
| Fuel Tank | 831.1 gal
| Fuel Type | diesel
| Horse Power: Sae J1995 | 1492 hp
| Number Of Cylinders | 16
| Power Measured @ | 1900 rpm
| Cooling System | 116.5 gal
| Displacement | 3051.2 cu in
|
---|
|
Drive System |
Emergency Brakes | Automatically applied prior to hydraulic system pressure dropping below level required to meet secondary stopping requirements.
| Parking Brake Type | Spring-applied, hydraulically released, with speed application protection.
| Service Brake Type | all-hydraulic actuated
| Wheel Brake Locks | Switch-activated
| Hoist And Steering | Dual, in-line, high pressure
|
---|
|
Operating Specs |
|
Hydraulic System |
Hydraulic System | 210.1 gal
| Pumps | Two pumps, single package, end of alternator
| Filtration | In-line replaceable elements
|
---|
|
Dimensions, Wheels & Tires |
Standard Tire | 37.00 R57
| Wheelbase | 191.61 ft in
| Width Over Tires-Front | 22.31 ft in
| Width Over Tires-Rear | 23.46 ft in
| Motorised Wheels | GEB35 Traction Motors
| Turning Radius | 446.2 ft in
| Overall Length | 449.48 ft in
| Overall Height | 223.43 ft in
| Front | Wheel speed disc. Three calipers on a 1213 mm / 47.75' O.D. disc
| Rear | Dual disc armature speed. Two 635 mm / 25' O.D. discs per side. One caliper per disc.
|
---|
|
Battery & Electrical System |
Alternator | 24 volt, 250 am
| Electric Dynamic Retarder (Max.) | 2387kW Continuously rated high-density blown grids w/retard at engine idle and reverse propulsion.
|
---|
|
Transmission |
Motor Gear Box | 10.1 gal
| Maximum Speed (Km/H) | 64.5
|
---|
|
Technical Specs |
Ratio | 30.8:1
| Control | AC Torque Control System
| Lighting | 24 volt
| Cranking Motors | Two/24 volt
| Capacity - Struck | 77 yd3
| Heaped (2:1, Sae) | 111 yd3
| Payload | 399997.9 lb
| Structure | Flat floor configuration
| Canopy Sheet | 6 mm 0.24'' 690 MPa 100,000 psi tensile strength steel
| Front Sheet | 10 mm 0.39'' 1379 MPa 200,000 psi tensile strength steel
| Side Sheet | 8 mm 0.31'' 1379 MPa 200,000 psi tensile strength steel
| Floor Sheet | 16 mm 0.63'' Outer 19 mm 0.75'' Center 1379 MPa 200,000 psi tensile strength steel
| Crankcase | 59 gal
| Hoist Cylinder | Two 3-stage dual-acting outbound cylinders and internal cushion valve, over-centre damping.
| Relief Pressure | Hoist-17237 kPa 2,500 psi, Steering and brake-27580 kPa 4,000 psi
| Hoist Time | Power-up loaded: 19 sec, Power-down: 10.5sec, Float-down empty: 12 sec
| Turning Circle Diameter (Sae) | 89 ft in
| Reservoir | 135 gal
| Suction | Single, full flow, 100 mesh
|
---|
|